Cisco CCNA NetaCad Advanced Lab 200-301 v7

Description

Having trouble getting access to your lab during your Cisco Netacad classes?  Taking classes remotely?  Then a solid home lab kit is the answer!  This lab kit is designed to work inline with your Netacad classwork and be an advanced tool to supplement your learning.
This lab kit runs all IOS 15 devices to make sure you can run the commands you need to succeed.  We
include the rack and even back everything with a 90 day warranty.
All equipment is tested and fully functional.
This kit contains:
1-1941/k9 Router
2-2811 Routers
2-2960-TT Switches
1-3560-TS Switch
2-WIC-1T and Serial Cable
4-WIC-1DSU-T1v2 and Serial Cables
Power Cables
3 Crossover and 3 Straight Through Cables
Cisco DB9-RJ45 Console Cable
To top things off, we even include a huge lab eWorkbook to get you ready for your CCNA exam.
Our eBook are copyrighted, owned and published by CertificationKits.  This eBook will be sent on disc via postal mail.  Sending it by email or by any other digital delivery method is not allowed and violates eBay policy.
Chapter 1
Introduction to Cisco Routers
Lab 1-1
Identifying Router Components and Accessories
Lab 1-2
Router Connectivity
Lab 1-3
Identify Router and Switch IOS
Chapter 2
General Router Configuration Tasks
Lab 2-1
Cisco 1700/1800/2500/2600 Series Passwords & Password Recovery
Lab 2-2
Configure Login, EXEC, and MOTD Banners
Lab 2-3
Configuring the Password Encryption Service
Lab 2-4
Exec Timeout and Login Failure Rate
Lab 2-5
Upgrading the IOS on a Router
Lab 2-6
Cisco Licensing
Chapter 3           Terminal Server Setup
Chapter 4
Configuring Static Routes
Lab 4-1
Static Routing
Lab 4-2
Default Routing
Chapter 5
Configuring Routers using RIP/RIPV2 Protocol
Lab 5-1
RIPV2 Routing
Chapter 6
Configuring Routers using the EIGRP Protocol
Lab 6-1
EIGRP Routing
Lab 6-2
EIGRP Split-Horizon
Chapter 7
Configuring Routers using the OSPF Protocol
Lab 7-1
OSPF Routing
Lab 7-2
Multi-Area OSPF Routing
Chapter 8
Configuring Routers using EBGP Protocol
Lab 8-1
Border Gateway Routing Protocol(EBGP)
Chapter 9
Configuring Catalyst Switches
Lab 9-1
Cisco 2900/3500 Switch Password Recovery
Lab 9-2
Switching and VLAN Introduction
Lab 9-3
Trunking
Lab 9-4
VTP/VTPV2
Lab 9-5
Spanning Tree Protocol
Lab 9-6
Rapid Spanning Tree Protocol
Lab 9-7
Per VLAN Spanning Tree Protocol
Lab 9-8
Inter-VLAN Routing
Lab 9-9
Configuring an EtherChannel Link
Lab 9-10
Configuring EtherChannel Using PAgP
Lab 9-11
Configuring EtherChannel Using LACP
Lab 9-12
Configuring a PortChannel Interface
Chapter 10
Configuring Access Lists, VTY Access and AAA Authentication
Lab 10-1
Standard ACL
Lab 10-2
Extended ACL
Lab 10-3
Named ACL
Lab 10-4
IPV6 Access-list
Lab 10-5
Trusted Hosts
Lab 10-6
Controlling VTY Access
Lab 10-6
AAA Authentication
Chapter 11
Configuring Network Services
Lab 11-1
Cisco Discovery Protocol
Lab 11-3
DHCP, DHCP Relay & DHCP Exclusions
Lab 11-4
DNS
Lab 11-5
Configuring NTP
Lab 11-6
Configuring Logging to a Remote Syslog Server
Lab 11-7
NetFlow
Lab 11-8
Routing Redundancy with HSRP and VRRP
Lab 11-9
Simple Network Management Protocol (SNMP)
Chapter 12
Configuring Network Address Translation
Lab 12-1
Static Inside Source Address Translation
Lab 12-2
Dynamic NAT
Lab 12-3
Overloading an Inside Global Address
Chapter 13
Configuring Encapsulation Types
Lab 13-1
PPP Encapsulation
Lab 13-2
PPP PAP Authentication
Lab 13-3
PPP CHAP Authentication
Lab 13-4             Multilink Point-To-Point Protocol (MLPPP)
Lab 13-5             Point-To-Point Protocol Over Ethernet(PPPoE)
Lab 13-6
HDLC Encapsulation
Chapter 14
Configuring IPV6 Addressing
Lab 14-1
IPv6 Link Local Addressing
Lab 14-2
IPv6 EUI-64 Addressing
Lab 14-3
IPv6 Site Local Addressing
Lab 14-4
IPv6 Global Addressing
Lab 14-5
Configuring EIGRP IPv6 Routing
Lab 14-6
Configuring Basic IPv6 OSPFv3
Chapter 15
Configuring IPSec
Lab 15-1
Configuring an IPSec Tunnel
Lab 15-2
GRE Over IPSec Virtual Tunnel
Chapter 16
Installing & Configuring Cisco Configuration Professional (CCP)
Lab 16-1
Installing & Configuring Cisco Configuration Professional